BC Transistor Datasheet pdf, BC Equivalent. Parameters and Characteristics. BC from Micro Electronics Corporation. Find the PDF Datasheet, Specifications and Distributor Information. See detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet. ORDERING INFORMATION.

Author: Kaziramar Talkree
Country: Singapore
Language: English (Spanish)
Genre: Medical
Published (Last): 5 February 2012
Pages: 429
PDF File Size: 3.55 Mb
ePub File Size: 7.75 Mb
ISBN: 905-5-70198-291-1
Downloads: 16828
Price: Free* [*Free Regsitration Required]
Uploader: Voodootaxe

Just stick it in and see if it works transistors only. OpenForm Good luck with your project. This particular book goes through lots of theory and how things work.

What is the difference between bc and 2nA transistor. It is hard to tell you how to design something, when we don’t know exactly what you have, what your intentions are This is very well explained in Experimental Methods in RF Design; this book is almost mandatory for the amateur experimenter. However, that would be the best bet. Looking at the data sheets, you should be able to substitute with minimal changes.

How would I know what hfe value to use? If this question can be reworded to fit the rules in the help centerplease edit the question. This question does not appear to datadheet about electronics design within the scope defined in the dstasheet center. Your name or email address: Read the datasheets carefully and make your choice. W8NSIApr 20, Raman 18 1 1 4. Difference between difference between bc and 2n [closed] Ask Question.

BC Datasheet(PDF) – Jiangsu Changjiang Electronics Technology Co., Ltd

The larger the resistance value of the emitter resistor, the less the performance depends on hFE. Here are some tips on how to read a datasheet. By using our site, you acknowledge that you have read and understand our Cookie PolicyPrivacy Policyand our Terms of Service. Most datasheets provide a list of typical use cases for the component.


BC 데이터시트(PDF) – Jiangsu Changjiang Electronics Technology Co., Ltd

First you should understand how transistors work and what bv347 key parameters are. If you need more current amplification for same biasing voltages you might want to go for 2AN. The basic difference is the 2NA is explicitly labeled “switching mode transistor”, which explains the much higher collector current in the same casing. I have use bc for a project Water level indicator.

W0LPQApr 20, The book is used as an “introduction to diodes, bipolar and field effect transistors” at community colleges. Would I be able to substitute 2n or a 2n for a bc and still use the same resister values in the circuit? How each transistors are selected for each project? Probably the most important parameters for transistor selection in amateur amplifier circuits are Ft and Pd and, I suppose, Vcc ; Hfe is not critical. Without a curve tracer, how can you design a class A amp to compensate for variations in parameters such as hfe and hie?

Some people don’t like to hear the word read The data sheets for several transisters I’ve been looking at don’t make the hfe value very clear.

Register for a free QRZ account. Do not remember what the is and never heard of the other device. Can i use 2nA instead of bc? What does comparing the datasheets tell you? In a class-A feedback amplifier, Hfe makes little difference.


transister substitution question

Finally you have to compare the datasheets of multiple transistors to determine which one suites your requirements best. Then you should learn how to read datasheets in general. In response to your specific question; yes, the three transistors are much the same and can be interchanged. There is not much difference when it comes to electrical properties of the two transistors.

Trivial questions that only require reading the datasheets should be closed. NTE on-line cross reference If you have a part number, it is quite easy to cross reference semiconductors. As far bcc347 changing types, the A is an NPN device. You can have a look at the datasheets: It’s been used for this purpose for so many decades that inevitably, you should be able to find a copy for little scratch on ebay or Amazon.

Nor will I get into it. George – All of the transistors you mentioned are small signal AF. Making hFE less relevant The traditional low frequency dagasheet with an emitter degneration resistor is designed so that hFE, as long as it’s above a nominally low value such as ten, does not matter.

Does the usual design techniques for say a common emittor amp already take this into account?